How to Sharpen a Pruning Saw? A 5-Step Guide
It is obvious to see the blade of the pruning saw become blunt one day, and won’t tackle the difficult job anymore. So, there is no way without sharpening the blade and getting it back on the track.
With the dull blade, you will sweat a lot. It makes you exhausted like you never felt before. Therefore, it is the final call to you to learn how to sharpen a pruning saw.
After getting to know how to sharpen a saw, you may not only save your effort but also save your valuable time as well. If your saw takes an hour to finish a job whereas it took less time to complete the same position, then it is high time for sharpening the blade.
No worries, we sorted it out, and now on, going to share the hacks with you. Grab a Coffee, seat back, and grasp the whole article below:
Step 1: Lookout & Clean the Debris
Every garden tool requires cleaning during its lifespan, so no exception with your pruning saw. Before head-starting the sharpening task, you need to clean the blade thoroughly.
To perform so, be equipped with brushes, a water Jar, and cleaning solutions. Again, never forget to wear a pair of protective gear like goggles and gloves.
This protection will save you when accidentally any wooden chip gets into your eyes. As you have armor and weapons so let’s get started.
The very first thing you need to do is to remove the wood chips also, examine whether any stains remain on the blade or not. Now gently run across them and scrub it carefully
You may find most of the debris out of the blade teeth where the wood stains get attached and stubborn to come out.
Once you are done with the scrubbing work then pour a 1/2 liter of water solution into it. Instead of it, you may soak it under a water prepared solution of vesin for 10 minutes. During that time, the solution will fully absorb the saw and easily remove all the rust and stain out of the saw.
Other than this debris, you may often find sap on the saw. In that case, Kerosene would be effective in combating it. So a wet piece of cloth applying a liter of Kerosene then gently rub across the blade teeth.
So when you keep rubbing across the sticky places, then the sap will begin to disappear. Remember, these kinds of sticks settle on the blade firmly, so you need to work hard.
Using Kerosene is pretty effective, and no matters how stubborn it is, the stain will go away. Just actively get your hands on it, then clean & rinse thoroughly.
Step 2: Bring out the Saw from the Frame
While removing off, the pruning saw out of the blade; the manual seems helpful. Read it carefully to know the process and get back to work.
This kind of hand saw sharpening tools applied for cutting the heads of the tree branches. So, the removal process seems a bit easier for you as you need to pull the blade apart from the tip of the saw frame.
Step 3: Let’s Start Sharpening
While sharpening a hand saw or pruning saw a piece of grinding rod is a must. Now you need to use it in the groove in between the teeth.
If you never heard of the grinding rods or never saw it before, then don’t get worried because this kind of rod is available in any hardware store to buy.
Once you purchase a piece of them and get back to work make sure, you wipe & clean it as well. Now, fix the rod against the crevices between teeth and push it forward forcefully.
Apply the process repetitively six to seven times across the pruning saw file and then reposition the grinding bar to new crevices. Do it this way until you reach the last crack or the gap between teeth.
- Five saw files with different sizes that should cover most...
- Made in Portugal by Tome Feteira, a highly respected tool...
- Made from high quality chromium alloy steel and hardened...
- These American pattern taper saw files have a triangular...
- The coarseness grade of these files is second cut (medium) a...
Step: 4: Remove the Burs
Have you ever been come to see burs on your saw? Once you have completed the sharpening process, they come to visible on your saw blade. To sort out the issue, you need to have a sharpener or hand saw sharpening files.
So use it on the rear side of the blade and eliminate all the burrs. To perform so, you need to scrub it three to four times.
Step 5: Lubricate and Complete the Task
Saw blade is a pure metal, and you need to feed it with lubricants. Once you have done the cleaning and grinding job, then make sure you use lubricating oil. Therefore, the average blade lifespan will increase.
Because the Lubricating oil never allows developing rust across the blade. So, make a solution of this anti-rust oil and use it when you come to see the dry edge after cleaning.
Now on, you have fairly done enough things to sharpen the pruning saw. So let’s see the level of sharpness of your branch saw.
While examining it, you will get to know the saw blade will cut through the tree branches more effectively and apply less muscle power. Holla! You have just done it and make your day great!
Additionally, you can check out our “How to Use A Pruning Saw?“
Final Words:
Never forget to keep the protection, so wear eye-glasses and hand-gloves before you start sharpening a pruning saw. Another thing is to make sure it is to buy the proper grinding rod in terms of size. For that, it will quickly get fixed next to the blade grooves, and so you may make it sharp. Hopefully, this article uncovers all the confusion, and now on, you can get your hands on it.
